-
Overview
-
redpesk OS releases
-
Security updates
- Security CVE / errata
- CVE quick look
-
Redpesk OS Tips and Tricks
-
Application Framework Manager
-
Application Framework Binder
-
APIs & Services
-
Security manager
-
OP-TEE within redpesk
-
Trusted Boot
-
Recovery features
-
redpak
-
Minimal image
- Reduce image size
- Optimizing boot time
-
Kernel fragments description
- Introduction to Linux Kernel Configuration
- 01 Disable IPC, Timers and Audit
- 02 Disable Kconfig, Scheduler and Initrd
- 03 Disable Perf, Profiling and Errata
- 04 Disable EFI, Power Management Debug and Energy Model
- 05 Disable Schedutil, CPUFreq Governors and Virtualization
- 06 Disable Kprobes and Jump Labels
- 07 Disable GCC Plugins and Function Alignment
- 08 Disable Partition Parsers
- 09 Enable Inline Spinlocks and Kernel Operations
- 10 Disable Swap, Memory Hotplug and KSM
- 11 Disable Networking IPv4, IPv6, Netfilter
- 12 Disable SCTP, VLAN, TIPC, BATMAN
- 13 Disable Wireless, Bluetooth, CAN and RFKILL
- 14 Disable PCI and Firmware
- 15 Disable GNSS and ProcEvents
- 16 Disable Block Storage NBD and AoE
- 17 Disable EEPROM and Misc Drivers
- 18 Disable Network Device Drivers
- 19 Disable PHY Drivers
- 20 Disable PPP, WLAN Coexistence, and Failover
- 21 Disable Input Devices
- 22 Disable Serial, TTY and TPM
- 23 Disable I2C, Power and Sensor Drivers
- 24 Disable MFD, Display and Media Drivers
- 25 Disable USB, Sound, RTC and VirtIO
- 26 Disable Filesystem Encodings and Compatibility
- 27 Enable Minimal Cryptographic Core with SHA3 and XTS
- 28 Disable Hardware Cryptography, Keep DRBG and Jitter Entropy
- 29 Disable Kernel Debugging Features
- 30 Disable Filesystem Verity and SecurityFS
-
Zephyr in Redpesk
-
PERM-CHECK extension
-
Mender redpesk (OTA)
-
Hardware support
- Download images
- Image metrics
- Trusted Boot
- Graphical support
- Boards - ARM64
- Boards - x86_64
- Boards - Virtual
- Boards - Archived (legacy)
- Miscs
-
Building microservices natively within SDK container
-
Building microservices and framework from sources
Intel UP Board 7000
The Intel UP Board 7000 is the current redpesk x86_64 reference board.
The board is based on the Intel Processor N-series platform and provides UEFI firmware, onboard eMMC storage, Ethernet, HDMI and USB connectivity. See the UP Board 7000 product documentation for hardware specifications.
Download images
Current x86_64 images are available from the Download images section.
Download the x86_64 image from the command line
Create a directory to download the image:
mkdir -p ~/redpeskimage
cd ~/redpeskimage
Download the current generic x86_64 redpesk image:
wget -r -nd -nc --no-parent \
--accept-regex='redpesk.*smack.*\.(bmap|xz|sha256)' \
--reject-regex='(image\.raw|ova|index)' \
"https://download.redpesk.bzh/redpesk-lts/corn-3.0-update/images/smack/minimal/x86_64/generic/"
Check image integrity
Before flashing the image, verify the downloaded archive:
sha256sum -c redpesk*.tar.xz.sha256
A valid image reports OK.
Flash the image to a USB drive
Identify the USB drive
Plug the USB drive into the host and identify its device path. Make sure you select the correct device because flashing overwrites it completely.
lsblk -dli -o PATH,VENDOR,TYPE,HOTPLUG,MODEL
Set the target device, for example:
DEVICE_TO_COPY=/dev/sdc
If only one block device is hot-pluggable, it can also be detected with lsblk and jq:
DEVICE_TO_COPY=$(lsblk -dlJ -o PATH,VENDOR,TYPE,HOTPLUG,MODEL | \
jq -r '.blockdevices[] | select(.hotplug == true).path')
echo "$DEVICE_TO_COPY"
Unmount the USB drive
Check whether any partition is mounted:
lsblk "$DEVICE_TO_COPY"
Unmount each mounted partition before flashing it, for example:
sudo umount /dev/sdc1
sudo umount /dev/sdc2
Flash with dd
Extract the image:
tar xJf redpesk*.tar.xz
Then flash it:
sudo dd if="Redpesk-OS.img" of="$DEVICE_TO_COPY" bs=4M status=progress conv=fsync
Flash with bmaptool
The image can also be flashed with bmaptool:
bmaptool copy "Redpesk-OS.img" "$DEVICE_TO_COPY"
It is also possible to download and flash the current image directly:
bmaptool copy \
"https://download.redpesk.bzh/redpesk-lts/corn-3.0-update/images/smack/minimal/x86_64/generic/image.raw.tar.xz" \
"$DEVICE_TO_COPY"
Boot the UP Board 7000
Plug the prepared USB drive into the board together with a keyboard and display.
Use the UEFI boot menu to select the USB drive as the boot device. Refer to the UP Board 7000 documentation for board-specific firmware and hardware information.
After redpesk has booted, application deployment follows the generic Application deployment workflow.